APM 2.8 V2.8 ArduPilot UAV Flight Controller & Neo-6M & GPS Antenna Foldable Stand Amount & Power Module & 433Mhz Radio Telemetry Transmision
APM2.8 and GPS
This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.5+, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.
The APM 2.8 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor
vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.This revision of the board has no onboard compass,
which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often
easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too).
This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.
Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally
Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
Onboard 4 MegaByte Dataflash chip for automatic datalogging
Optional off-board GPS, uBlox LEA-6M module with Compass
One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000
Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties
Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively
Built-in compass GPS module
Main chip: Ublox-6M
With fast satellite searching speed and high precision
Compatible with APM serial port and I2C port
Includes round plastic shell and GPS support
3DR Radio Telemetry Kit 433Mhz
The 3DRobotics 3DR Radio is the ideal way to setup a telemetry connection between your APM and a ground station. Small, inexpensive and with great range, the 3DR radio uses an open source firmware which allows us to do things that cannot be done with other radios.
Very small size
Light weight (under 4 grams without antenna)
Available in 900MHz or 433MHz variants
Receiver sensitivity to -121 dBm
Transmit power up to 20dBm (100mW)
Transparent serial link
Air data rates up to 250kbps
Range of approx 1 mile
MAVLink protocol framing and status reporting
Frequency hopping spread spectrum (FHSS)
Adaptive time division multiplexing (TDM)
Support for LBT and AFA
Configurable duty cycle
Built in error correcting code (can correct up to 25% data bit errors)
Demonstrated range of several kilometers with a small omni antenna
Can be used with a bi-directional amplifier for even more range
Open source firmware
AT commands for radio configuration
RT commands for remote radio configuration
Adaptive flow control when used with APM
Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF microcontroller.
MAVLink-OSD is an Arduino based project and it is fully compatible with original MinimOSD.
This board can be used for CRIUS AIOP and Arduflyer / ArduPilot-Mega.
MAVLink-OSD with switching DC/DC stepdown powersupply to maximize efficiency on power system. No more heating problems when using this OSD board.
Default OSD Firmware is MinimOSD-Extra, written by Gábor Zoltán.
About how to use the configurator tool to setup OSD function: Click here
How to setup hardware (original MinimOSD Wiki): click here
Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 7S LiPo battery.
Note: The Power Module is only designed to power APM/Arduflyer, a RC receiver and accessories (GPS, Radio telemetry). It is not designed to power servos. Use your aircraft's own ESC/BEC for that.
MAX7456-EUI monochrome on-screen display
5V/500mA DC/DC regulator for MAX7456-EUI
Operating voltage: 5V(FTDI connector) and 12V(Video I/O connector)
Supported NTSC & PAL video format
Full MAVLink protocol support
Graphical configurator tool
APM Arduflyer Power Module V1.0
Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements,
Package size: 19 * 10 * 5cm/7.6 * 4 * 2in
Package weight: 190g/6.7oz
Adhesive taps package
1 * APM 2.8 V2.8 ArduPilot
1 * Neo-6M
1 * GPS Antenna Foldable Stand Amount
1 * Power Module
1 * 433Mhz 3DR