22.26Inclusive of VAT
Price on the app only:
Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
Questions & Answers
I am not sure. It fit and older losi baja mini-t. 1/16 1/14 scale.
By Anthony S. on May 23, 2018
It has various screw to accommodate most builds. If you're replacing a motor this size it will fit.
By Caleb Oates on May 16, 2018
Dromida 7.4 2200mAh 20c 17wh LiPo battery
By Vanora on May 9, 2018
The steering servo attaches to a receiver (also known as RX) not the esc.
By RBaird on May 5, 2018
I have this in a WLToys A252 1:24 scale drift car. I run it till the lipo cutoff 2 batteries backti back. Hasn't got hot, been running strong for weeks.
By BoilingOil on May 5, 2018
Yes it should mount right into a rock crawler, however it is not the right type of motor for crawling as it is lower on torque. Hope this helps!
By ExplosiveRC.TN on April 2, 2018
Yes, It will take a lipo and it does have a low voltage cut off. This motor runs hot. I would install a heat sink on the motor. I did on mine.
By Larry on March 30, 2018
If its1/18 yes if any bigger might beed to modify either buggy or kit
By sause on March 30, 2018
Yes it will!
By RBaird on March 10, 2018
Please note that TOMTOP Forums are a community for all communicating and getting help each other. There will be some enthusiastic friends participate in your discussions. Of course TOMTOP customer service (with tomtop customer service icon) response is guaranteed ,which is the same way you contact us at http://www.tomtop.com/contactsopen this forum in full page
based on 46 Customer Reviews
Share your thoughts with other customers and get Tomtop Points, the first 5 reviews get DOUBLE Tomtop Points!Write a Customer Review
June 13, 2020
I installed it in my 1/18 LaTrax Teton (with a 2s Lipo battery). HUUGE difference. Too fast to handle but a lot fun. Well worth the price for the fun of it though. I did not need any special modification to make it fit or screw it to the motor mounting plate - just some double sided tape to secure the ESC. I also increased my gear ratio which made it insanely fast - the tires fly right off if they are not glued. I also put larger wheels on later - thats when things really started to break things. Don't do that... this is perfect on a 1/18 scale with a 2S lipo - but glue your tires ;)
By Bonnie Hott
May 18, 2020
By Matthew R Bailey
February 4, 2020
One of my main goals with this was to try 3S in my heavily modified Latrax Rally. No-go.....the ESC just blinks red when plugged into 3S. I have the programmer, tried various low-voltage cutoff settings (including 0 volts), two different batteries at various states of charge, tried plugging in the programmer while running off 3S. This is a big bummer for me, will probably just have to order a different ESC. Product description needs to be updated for sure. Noticed another oddity. Near full throttle, the RPM "jumps". That is, throttle response is relatively smooth and linear up until just about max throttle. There is a clear and obvious jump in RPM. Not a big deal for bashing a Latrax, but I could imagine this causing issues for racers. On the plus side, when paired with a 20t pinion, my little Rally hit 25mph (stock with the 2S is around 20mph). That's a respectable increase, and there's still tons of torque. It subjectively seems to have more torque on the 20t than the stock brushed has on the 14t (I used to notice the brushed motor bogging down when turning hard). If you're happy with 2S (which, really, is about all the Latrax cars can handle without some serious re-engineering), then this is probably a good choice. It did slide in with no mods required, and the stock motor bolts mounted right up.
November 23, 2019
Motor has been a nice upgrade over the stock LaTrax Teton motors. My sons have burned thru several of them. I purchased this motor along with the programming card, but the motor was fine out of the box. There is a bit of a delay between squeezing the trigger on the remote and the response on the vehicle. Have now broken some drive components on the LaTrax since switching to this motor. The LaTrax line is not very durable and probably not ready for this more powerful motor.
By Michael Wong
November 22, 2019
By Simple Man
November 5, 2019
October 8, 2019
A great combination of cars with 1/18 ratio. I used it on the Latrax SST (4x4 truck at 1/18 scale) and it seems to be powerful enough. I really need to install some M2.5 screws, but otherwise replace the replacement motor directly. ESC exceeded my expectations for this price. It is very difficult to make this system work (as long as it is configured correctly). The ESC or motor will not overheat, especially when compared to a conventional brush system that is to be replaced. Not sure how others burned this system. Larger vehicles, excessive transmissions, transmission line drag and turf driving are variables that can exceed the limits of this engine, but if used within a reasonable range, this seems to be a very reliable system. .
October 7, 2019
October 6, 2019
It usually combines perfectly with Latrax or 1/18 cars. Powered by Lipo, the touch engine always looks great. Keep in mind that, starting with the differential spider gear, it will destroy almost everything else in the Latrax car ... I have both the original Latrax / Traxxas and the trans / recv of the aftermarket, which work very well. However, it is a bit too fast.
October 6, 2019
October 5, 2019
October 5, 2019
October 4, 2019
This is my second scenario. I could have put 33 packages of grease with voltage protection and shot blasting, and everything should be fine. I just bought one for my 5-year-old son (I already have my) and other Mamba mini gloves, so I think it's enough to deal with his 18th-order rock drill. The best update is $. The price of my castle is five times the price. Get the program card to customize start, stop and low voltage. Keep it clean and unobstructed, this will last a while. Oh, did I mention it as fast as crap? The perfect nimh Crazy fat man.
October 2, 2019
It is perfect for Latrax Rally without modification, but you will need two different screws, and I have reused some of the M2 hexagonal screws that I have equipped for the 1/16 Revo. It doesn't feel much faster than a normal engine, although it may be because it takes too long to pull a normal tire, but running a 2S lithium battery won't be too hot, I haven't broken anything, so A +! Advantages: Directly suitable for Latrax cars with 1/18 ratio. Good power has not damaged the parts of the inventory, it is still suitable for storage. The sprockets will not overheat the Lipo fuses (not tested). It doesn't have the right size or tone (Meh) doesn't show "GoolRC" anywhere, it looks like a cheap universal set (hmm ... this is the case). There is no programming card, and it seems impossible to program except one Nothing The ESC seems cheesy because the pieces of cheddar cheese are sitting on a Swiss plate. To be honest, this is a circuit board with a heat sink connected, although it works. The ESC and motor cables are not insulated from silicon. In general, it is cheap, it works, it meets my requirements and Lipo needs to take deficiencies seriously. The only thing that really bothers me is the built-in programming method. If I want to change something, there is nothing to say what programming card is needed.
December 7, 2015
November 26, 2015
November 19, 2015
November 1, 2015
October 7, 2015
October 6, 2015
Top Sellers More>
Your question has been submitted successfully
Please activate your account first. We will resend the activation email to help you complete your registration.
OUR SITE RUNS OF COOKIES