Mouse over to zoom in
Price:
US$
41.99
Loading...
Ship to
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
`1
Questions & Answers
For some reason you have to reposition the left stick so it goes up and down instead of side to side. The right stick is shared with the rudder
By Jimmie Hawkins on April 6, 2018
Yes throttle is on left has click lock for steady speed control
By Joe R. on February 4, 2018
Can you send me a picture? Post a picture here... I'm not sure what you mean exactly.
By Mike Fas on April 27, 2018
I'd say it's good for both. Servos will depend on the size plane or car you are working with. They won't really have anything to do with this. I'm personally using this for my remote controlled lawnmower.
By Mike Fas on April 26, 2018
I found one by the way googling the part number or there website
By dave on April 11, 2018
No. It is not programable. It's set for the reciever that comes with it
By James Barker on April 4, 2018
I m no sure, I just try about 300 or 350 feet and I sure it's working good. I hope you serve.
By Mercedcandia on March 25, 2018
The receiver should, but you're going to need a controller board on the quadcopter itself
By Malachi Allison on March 20, 2018
Yes, however this transmitter is designed for aircraft and uses a aircraft frequency. I think you would be more comfortable using a transmitter with a wheel steering than using sticks. If you are buying it so you can use all 6 channels then yes it will work.
By bob lucus on March 4, 2018
Discussions
Please note that TOMTOP Forums are a community for all communicating and getting help each other. There will be some enthusiastic friends participate in your discussions. Of course TOMTOP customer service (with tomtop customer service icon) response is guaranteed ,which is the same way you contact us at http://www.tomtop.com/contacts
open this forum in full pageAverage Rating:
4.3based on 126 Customer Reviews
Share your thoughts with other customers and get Tomtop Points, the first 5 reviews get DOUBLE Tomtop Points!
Write a Customer ReviewBy aotellin
April 20, 2020
The transmitter is easy to operate. The range is acceptable. The weakest part is the antenna - if you grab the transmitter the wrong way or accidentally drop it, the antenna will be broken. I broke two antennas, replaced one with the similar, the result was so-so. I switched to FS -i6
By Howard
July 2, 2019
By Arthur
July 2, 2019
By Jessie
July 1, 2019
By Julian
July 1, 2019
This is not your best Spektrum launcher, but I will never complain about the $ 40. Personally I use it as a protection against faults for my house, an arduino-based quadcopter, so far it has not given me any problems. I have never used the included CD because there are many good resources on the web about how to install the driver and make the receiver work. One thing that is not mentioned in the list of products (look for T6config) is that it requires 8 AA batteries (consumed in approximately 20 minutes of flight) or 12 volts of power. Quickly I chose an external 12 V power supply and flew out of the car battery or the DC power supply plugged into the extension cord. I think I can buy a LiPo bag in the future. But now, I really like it, I do not need to buy 8 AA each time I fly. The plastic feels a bit cheap, and it does not seem ridiculous to have any battery weight, but it really is your job. As I said, I use it as a protection against faults, in case my arduino-helicopter is out of control, I can return it. I have not touched it on most flights, but it saved me a couple of times. Exceed RC has an excellent interface program that allows you to save and load different profiles on the transmitter. Honestly, I have not used this function yet, because I only use it for one of my quad cores, but it seems that it could be useful for more serious RC people. I bet they paid more than $ 40 for the pitcher, so I'm not sure how useful it is. Maybe I should pay attention to one thing: my transmitter does not have any knobs on the joystick! This is not a problem, because I can use a bit of aluminum scrap to machine some knobs to stick them on, but it's really strange to get the bare shaft out of the package.
By John
June 27, 2019
By Robert
June 25, 2019
There are no real files. It is difficult to find an adapter that allows you to charge the battery. If you plan to use it for a robot, is it suitable for Arduino? But you need to test the channel to see its maximum and minimum values. I can not get the speed control of the vertical bar channel to show anything, but then I do not need it for my application. I suspect that it needs to be programmed with a CD program to configure your channel. I do not need to pair the transmitter with the receiver because they seem to be pre-paired.
By Martin
June 25, 2019
By Johanna
June 24, 2019
By Delbert
June 17, 2019
By ***
April 8, 2019
By s***2
June 2, 2018
By p***s
June 1, 2018
By b***n
May 26, 2018
By r***5
May 12, 2018
By j***k
May 5, 2018
By a***3
February 9, 2018
By m***t
February 7, 2018
By s***6
January 3, 2018
By A***o
December 6, 2017
