Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
Q & A
に基づいて 731 お客様の評価
By alfonso a. tobar
December 7, 2016
The RF-603 wireless unit can trigger both portable flash units or speedlites, and Studio flash units as well. Apparently, the maximum flash sync speed allowed in SLR's or DSLR's is their maximum sync shutter speed for that camera provided transceiver is used as pass through for a flash unit (*). [In my Nikons D300S, 1/320s (Auto FP) and 1/250s (Auto FP) are maximum sync shutter speeds]. My tests were performed in a Nikon DSLR D300S, and maximum sync acceptable shutter speed, however, was obtained at 1/200 and below when one transceiver was used in the DSLR's hot shoe as a transmitter and another as a receiver in an off-camera flash. Therefore, I found that maximum flash sync shutter speed will decrease and this was very noticeably in my random tests. Therefore, the highest max sync shutter indicated by the manufacturer will be ONLY valid for the on-camera flash when transceiver is used as a pass-through on-camera. Secondly, the transceiver by itself can not be used to test fire remote flashes with transceivers acting as receivers in flash units. (Open Flash Test triggering not supported.) (*) 1/250 sec sync shutter speed can ONLY be obtained when Flash unit is mounted directly on the camera hot shoe as a pass through. Please see more photos at shutterbugcl DOT blogspot DOT com. I noticed a few misfires probably because I must have done something wrong. The RF-603 were tested out of the box. For a detailed review and sample photos, please visit shutterbugcl DOT blogspot DOT com. The overall performance was excellent anyway. Great results! --- UPDATE [Nov.27_2011]: I bought these units to be specifically used with the new Fujifilm X10 12 megapixel EXR CMOS Rangefinder Camerato be released by November 9, 2011 that I have already pre-ordered from AMAZON. In the meantime I decided to perform test runs to make sure everything was OK. Wireless are great for any camera model and manual flash units. Unfortunately, they do no work with new Fuji X10 or X100 rangefinder cameras. Wireless Transceiver Pins are not thin enough to communicate with their hot shoes. By LATIN IMAGE Photography latinimage DOT blogspot DOT com ---
By R. J. Lowe
November 15, 2017
I bought 2 sets so that I could have one on-camera and fire 3 YN560 strobes. It works great for that. However: 1: The sync speed is a bit muddy - I use a Nikon D7000, whose sync speed is 1/250. These triggers have a tough time at 1/200 where you still see darkening on one edge of the image. At 1/250 nearly half the frame is dark. You really need to step down below 1/200 to get acceptable images without 'catching' the closing curtain. 2: You cannot turn the units off/on with the flash mounted. Seems like a dumb design mistake since the triggers and the flashes are both from Yongnuo. The flashes ride nearly flush over the top of the on/off switches - which should have been located on the side of trigger - seems obvious, but they didn't do it that way. So now both the triggers and the flashes will get much more wear & tear mounting and unmounting just to turn the units off/on. Dumb. If you can live with those caveats, the units are great and I haven't had any other issues with the set-up described.
November 11, 2017
I have used these wireless triggers in my photo classes, and they work great. HOWEVER, when I ordered a set of 4 for myself (2 sets each), each set comes with the two triggers and one cord. It is the cord I have a problem with. This cord is to plug into your camera, not studio lights!!! WHY did not a set of cords come with these remotes that I could use with a studio strobe flash? Now I have to order 3 new cords! I am not a happy camper because I think for the money we spend on this item, we should be provided also a cord that can be used to hook up to a strobe flash! Yongnuo you are stingy!
October 23, 2017
This trigger system is super easy to use and has worked very well. I have only had a few instances where it failed to fire my flash. Easy to pair with the Yongnuo YN 560 III I bought at the same time. You set the channel with dip switches on these and you can easily match it on the flash itself. Don't expect the wireless trigger to work unless you verify your camera has the correct input for the cable provided. Overall, these are an awesome value when you're building a system on a small budget or aren't going to be using all the time.
October 18, 2017
Took zero setup to configure to work with the YN-560 III for wireless triggering. Good range. I had my camera located outside, trying to get shots of the meteor shower a few nights ago and was able to trigger the camera from the warmth of my room. Unfortunately - cloud cover didn't net me any asteroid photos. Either way, the trigger worked great. Though - it should have a threaded hotshoe - so it can be connected to a light stand or tripod. Only reason it loses a star. Kinda wish they'd come with some sort of carrying case, too. But, at this price - very happy.
October 16, 2017
I wish I had switched to this sooner. For such a small price, it provides so many functions, the other brand (especially like Pocket Wizard)should feel the pressure and shameful. Pro: 1. multiple useful functions: wireless flash trigger and shutter release. which could enable single person to accomplish complex photography job. 2. AA battery based!! ( looking for this feature for long time) 3. transmitter and receiver in one unit 4. 2.4 G wireless spectrum and long range possible ( 100 meter range not tested but most of in-door photography can be done) 5. additional hot shoe!! (looking for this feature for long time) 6. additional Sync port. 7. works great with my Nikon D700 and speedlight SB-700 and speedtron 2403 (with 102 head), Sync speed 1/250 has no issues. Cons: 1. No test button; it has to be fixed to the camera and flash and then can be tested to see the connection. For this, I deducted one star. I don't think it's an issue for me but it might be issue for other people relying on TTL. So I have to list it here: it does not support TTL. However for $ 32, that's very sufficient to accomplish most strobist work!! So far I love it.
September 1, 2017
The package contains two transceivers; one functioned properly, the other would not. I tried multiple sets of batteries and could not get the power light to illuminate. My only return option is to send it back and receive a refund. I'm going to order another set and give them one more try. *** Update *** The second set works as promised. I paid for two day shipping, and they arrived in five days. I haven't had a chance to try them out much, but I can set up the camera at one end of my house, walk to the other end, press the trigger, and it works- through multiple walls, with no line of sight.
By Chuck Friel
August 19, 2017
Terrific performance at a bargain price. Have worked flawlessly since purchase, in fact I purchased two(2) pairs of Yongnuo RF-603 triggers. They work through walls, and around corners thanks to RF not LED signaling. So, big deal they don't pass TTL data. So what. I use them with my Nikon SB-600, SB-800, and SB-900 flashes without issues. At this price you can continue to purchase inexpensive pairs and simply dispose of units IF and WHEN they fail. Highly recommended for amateurs and frugal Pros.
By Jonathan Lee
August 18, 2017
Very affordable alternatives to expensive solutions. Used with SB-600 Good: Cheap. Act as transceiver and receivers. Works well with manual flashes. Bad: On occasion they seemed to lock up my flashes when connecting and wouldn't fire (may be something with the flashes). Doesn't wake up flashes from "sleep" mode (have to physically wake up the flashes before continuing). Overall: Recommend as a cheap alternative that works most of the time. It is a system that can expand as you need it. Would like to try with different flashes and lights.
By Mitchell J. Martin
August 17, 2017
I purchased two sets of these to trigger my SB600 and Yongnuo 560 flashes off camera. I had purchased the Yongnuo 602 set a few weeks earlier and wanted to expand with the addition of the new flash. I tested these at home when they arrived and then took them out to a portrait shoot in the woods. They work great. No issues with missfires. The only con I can mention is that the on/off switch is diffcult to impposible to use one the flashes are mounted. You simply have to remember to turn them on before use. If you are looking for a cheap and reliable wireless trigger system this is the product you want.
By Peter Miller
August 5, 2017
These flash triggers are easy to set up and use; just understand that you can't use TTL metering to set flash strength - you have to adjust the flash strength manually. What I really like is the wireless shutter release - you can fire the camera remotely, even the camera and flash remotely together, which is great when you want to move the flash around between exposures. The shutter release buttons on each trigger has a definitive halfway point when you press them, so you can autofocus before you release the shutter. These triggers seem to be well constructed and a terrific value.
August 4, 2017
In a land not far away lived a photographer. He was a nice, but quite cheap man. It came a day when he had to place his flash away from his camera (he was a newbie). For a long time he struggled and got mad at his camera for he was only able to trigger the flash by having it on slave mode and using his built in flash while trying to angle it away with his hands so that he doesn't get harsh lighting. He finally had enough and he knew what he must do. He went on the interwebs. Searching everywhere for the best triggers, but all he found were Factory made ones that cost more than even a Starbucks Coffee! But at last, he came across the Yongnuo RF-603 II N3, and his mind was blown. The build. The quality. The price - it all made so much sense! He bought many of them and told all of his friends about them (he had none). Seriously, get these, they're awesome.
By Larry Jordan
August 1, 2017
The Yongnuo wireless triggers are a great alternative to PW's in some situations. If you are in close quarters in a controlled environment, these triggers will do everything you need. They are easy to set up and I have never experienced one false trigger with my Nikon D70/SB 800/SB 900. I have only used them to control speed lights at a maximum distance of 50-60 feet. I have no experience using them to trigger a camera body which they can do. If you are just starting out with portraiture or wedding photography and are not yet able to spend more on PW's, these will easily do the job especially in a controlled, predictable setting. Be sure to order the model specific to your brand and have fun.
July 17, 2017
Extremely happy with this product. I bought two sets of these to go with my camera and three flashes. I really like that these are transceivers as I lost the transmitter on a previous version which ended my shooting. They are extremely reliable for the price. One of the best features is that you can remotely trigger your camera with the included cable. It works far better than the cheap IR remote that I have because it reliably works outdoors at a distance (the sun effects the IR) and you can half press to focus. What keeps these from being perfect? They only sync up to 1/160 shutter speed. 1/200 gets a small black band and 1/250 is about a third of the image. I was expecting to get 1/200 and would have been happy to get 1/200. The only other negative is the location of the on/off switch is difficult to get to once mounted to your flash. Pros: Transceivers (not separate transmitter and receiver) Reliable (can be a problem with other knock-off triggers) Can use as a remote shutter release, including half press to focus Inexpensive Cons: Slow sync speed Location of the on/off switch
June 23, 2017
I had purchased this for my Nikon because of the ratings i had seen from others. This product does work for the D3100. Cost a lot less then other wireless triggers! I purchased two speedlights and decided i need another wireless flash trigger so i ordered two more. I am now able to utalize the two speedlights and set them off remotely with this trigger/shutter release. The reason I gave it a four star is becasue it does not work 100% of the time. Sometimes i get missfires. But it's worth the price.
June 17, 2017
Overall satisfaction especially when considering the price. I have a couple of these which I use in a double distant flash arrangement (two slave flashes). One of the flashes is a Youngnuo with built-in wireless and the other is a TTL Sigma (manual mode) mounted with one of the receivers. The second receiver is of course on the camera body. Shut-off performance is dependable. Funny enough, the Sigma looses all TTL capability when mounted over the receiver in the camera body. This is annoying when doing bounce flash photos. Overall, very pleased with the results. There's really no need to go for more expensive equipment. These do the job fine.
By Merciless Max
June 13, 2017
I was able to set them up so they work collectively with 3 strobes, 3 Yongnuo Flashes and the Nikon SB910. I took over 300 pictures in one photoshoot session and it misfires only once. I like how they moved the on and off switch to the side unlike its previous version. I used one on the camera Nikon 7100, held on in my hand to trigger and six more for my 6 light sources. I didn't use the slave mode on the strobes and had each connected to one. Make sure you get the cable that connects the trigger to your strobes.
By Stephen E. Duffy
March 24, 2017
BEWARE PENTAX USERS The trigger works in the camera hot shoe but Pentax brand flashes do not work when installed in the hot shoe on the receiver with out a bunch of "wiggling" or "nudging" which makes them unreliable. I gave them 4 stars because I feel that they work very well on the flashed they were designed for. I HAVE FOUND THAT THE RF-603II C1 WORKS PERFECTLY WITH OUT "WIGGLING" OR "NUDGING" AND COMES WITH THE CORRECT TRIGGER CABLE. YOU WILL ALSO NEED TO USE THE TRIGGER BUTTON ON THE TRANSMITTER TO WAKE UP THE FLASHES.
March 8, 2017
I already had 6 of the RF-603 units (earlier version) and they've been great. I've had few problems. But I did have a wish list of improvements, and the most important ones have all been added in the 603 II, so I'm very happy. I just received the RF-603 II. This new version can (1) be used to fire a test flash, (2) the on/off has been moved to the side, and (3) it can now be tightened down into the hot shoe. I almost busted a flash once when the older 603 version allowed my flash to slip out of the hotshoe and fall onto concrete. Luckily the flash still worked afterwards. Finally the 603 II corrects this problem. I appreciate that they are maintaining compatibility on the 603s. They've been a huge help to me, and have proven to be extremely reliable.
By Tim R Stacks
February 21, 2017
I purchased the RF-603 II-N3 flash trigger system to use with my two Yongnuo YN 560 III speedlights. These speedlights are non-TTL, so triggering was all I needed. This system comes with two identical units where one can be mounted to the camera and acts as the trigger; the other can be mounted to your off-camera flash and acts as a receiver. However, since my two speedlights are wireless, only one transceiver is needed to trigger both speedlights, which is really nice. I bought this for the Nikon camera system, but was really looking for something to use on my Sony A6000. The build quality is nice and it doesn’t feel or look cheap in my opinion. I tried it first on a Nikon D3100 and it fired right away. When I put it on the Sony A6000, it did not fire. I had read some other reviews about some difficulties people have had with using these on Sony cameras, including have to make modifications to the earlier models of this trigger to get it to work. I didn’t really want to do that, so I tried repositioning the trigger in the Sony hot shoe, or as Sony calls it, "multi-port." I first tried pushing it forward as far as it would go and it did not work. However, when I backed it out a little (somewhere between 1/64 to 1/8 inch, I’d guess), it worked like a charm and the flash fired. Evidently, the electrical contacts between the trigger and Sony’s multi-port do not align if the trigger is pushed all of the way in to the multi-port. I took it on location the next day. I mounted the trigger onto the A6000 and it again took me two or three tries before I found the sweet spot again. I locked the trigger down by tightening the plastic locking ring onto the camera, and shot for about three hours straight with it. It never budged or misfired. I am extremely happy with it! I’m giving this 5-stars, and I don’t blame Yongnuo for the electrical contacts not aligning up with Sony's multi-port. After all, I bought this for my Nikon and it works perfectly on that camera.