Preis nur auf die App:
Diese Seite wird jetzt geladen....
Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
Bitte beachten Sie, dass TOMTOP Forum eine Community für Ideenaustausch und Hilfe sucht, bei denen Tech-Enthusiasten an der Diskussion teilnehmen werden, mittlerweile wird TOMTOP Kundenservice (mit Tomtop Kundenservice-Symbol) rechtzeitig reagieren, mit der gleichen Funktion wie der Kontakt auf http : //www.tomtop.com/contactsÖffne dieses Forum in voller Seite
beyogen auf 379 Kundenbewertungen
Sagen Sie Ihre Meinung mit anderen Kunden und erhalten Tomtop Punkte, die ersten 5 Bewertungen bekommen DOUBLE Tomtop Punkten!Schreiben Sie eine Rezension
By Sourdough Don
December 25, 2017
After reading reviews of both this product, the Docooler Digital Temperature Controller and the similar STC-1000, I realized that this unit does exactly what I want: a unit that I can re-purpose easily to either heat or to cool, with one power plug and one receptacle for the plug on the unit I am controlling. I use this to control either heating my bread dough to its optimal proofing temperature, or cooling my beer to fermentation temperature. I never need to have a set-up that can be configured and then switched between heating and cooling, like your home heating/air conditioning. Thus, I only need one receptacle to plug into, not two, as would be wired with the STC-1000 units. The good news for those buying this now is that the instructions are much clearer, including the wiring diagram. I did get mixed up with the low and high limits, thinking that I needed to set them to control the temperature, but the unit does that via the parameters, so all you do is set the target temperature, which comes up when you press “set”. I was pleased that the connection terminals accepted two 16 gauge wires, so the trick I used with my earlier controller worked fine: I took a 12-15 foot extension cord, cut it in half, and used the plug/male half to power the unit and supply the ‘hot’ side of the relay, and wired the receptacle/female half to accept the switched hot from the relay and get neutral from the plug half, via the shared neutral input on the controller. I only needed one jumper wire between the hot into the controller and the hot side of the relay, as pictured both on the unit and in the instructions. As always, consult someone with good experience with electrical wiring to confirm that you have hot and neutral wired correctly.
December 25, 2017
J'ai acheté ce regulateur pour équiper un vieux chauffage dont le bilame avait un énorme hysteresis. Il remplit bien sa fonction, pas bien compliqué a connecter, s'encastre proprement et solidement dans la fenetre que je lui ai découpé. L'hysteresis minimal est de 1°, pour réguler la temperature d'une chambre ca aurait été préférable de descendre un peu en dessous de ça mais malgré tout c'est très convenable pour ce tarif. J'enlève une étoile parce que j'ai une odeur de plastique chaud lorsque le radiateur est en service alors que le régulateur est positionné en dessous, je pense que le type de plastique utilisé ne supporte pas du tout le moindre rayonnement.
December 25, 2017
Ordered this to control some fans in our rabbit barn. Needed reasonable accuracy -- the analog ones we've tried varied from day to day by 5 degrees or more. Received the controller before they said I would (does ship from China). The instructions are readable but not the clearest. Thanks to several reviewers who have additional helps on operating. Wiring is fairly simple -- wire the load to two contacts and provide power to two contacts and put the sensor to the last two. The first unit I received worked only in heat mode -- would not activate in cool mode. I contacted seller through Amazon and they promptly responded and determined unit was defective. They happily sent another unit with no hassle. Their customer service through email was very good though it takes time to cycle emails back and forth -- they seemed to reply within a couple of business hours. They sent me a second unit which I installed and it worked great. Been working now for two weeks with no hitches or problems. Seems to be very accurate +/-1 degree. Display is easy to read. Turns our fans on over 78 and off below 78 exactly as we need. For the money you are not going to find a better thermostat. Summary: great product which seems to work well; though the 1st one was defective they promptly replaced it; shipping was as stated (looks like they may have just gone prime so shipping might be faster now); works great as fan controller.
December 22, 2017
je l'ai monté dés réception en fait montage très simple (même si la notice est en chinois et en anglais) chercher sur internet ([...]) j'ai mis 15mn pour faire les branchements et 10mn pour le régler, question efficacité la nuit je l'ai branché sur tapis chauffant (dimensions 60cm/40cm) et régler à 30° de ce coté la j'ai un peu de perte (-2°) mais je n'ai pas trop poussé sur le réglage la T°du terra reste stable à 28°.6 ou 28°.9 toute la nuit à 5h45 un minuteur tout simple qui met la lampe uv à 40° EN 15 mn et deux néon du commerce qui s'allume et mon pogo ne s'en porte pas si mal, j'ai laissé dans mon terrarium un thermomètre classique la précision est excellente. pour le branchement :Branchement du thermostat arrivée secteur sur 3 et 4 (power) reprendre le 3 et le renvoyé sur le 2 entrée du relais (load) mettre le 1 (sortie du relais) en sortie remettre le 4 en sortie brancher les 5 et 6 sur la sonde de température voila pour les connections Utilisation appuyer sur set en température supérieur le thermostat va indiquer la T° ambiante appuyer sur set pour régler la T° de chauffage supérieure à atteindre puis maintenez la pression sur set jusqu'à et régler la fourchette de T° +ou- de mise en route ou de coupure,
By Lee Harrison
December 20, 2017
Product works well but it only lasted a year and a half before the contacts became frozen, and the timer was essentially stuck in the ON postion. This was particularly bad because I have it installed in a restored Coca-Cola cooler. Since it never turned off at 30F, the cooler got so cold it froze all the soda in the machine, and every single can exploded! It was a huge mess to clean up, and it took me a minute to realize how it even happened. I've purchased another one because the machine has been modified to fit this model specifically. Hopefully the next one lasts a bit longer. I have also noticed that the outer casing has been redesigned in the last year, with English replacing a large majority of the text on the unit itself. The instructions still suck though.
December 16, 2017
I use the digital temperature controller to monitor and control my aquarium temperature. It is very easy to set and very precise. I have ordered another one for my second aquarium. I will order one more to mix hot/cold water for water change. The controller fits perfectly into a $0.6 plastic electrical box (B122A size), which is available in any home improvement center. I spend less than $3.00 for extra material to build a very nice controller box - see picture. Many people complained about the poorly written manual for the controller. I would like to share my knowledge about this controller. I hope this Manual will help. Manual for MH1210F 10A 110V Digital Temperature Contoller with Sensor - NTC 77 Fahrenheit=10K B3435. Display Codes (Adjustable Parameters): HC H/C Heating or Cooling mode. CA -1.5 Temperature Calibration. -1.5 is my setting (default at 0.0 ˚F) which decreases measured temp by 1.5˚F. At the default 0.0 setting, my controller reads 78.5˚F and a good thermometer reads 77˚F; I entered -1.5˚F in CA, now the controller and the good thermometer have the same readings. PU 00 Delayed cooling start time (minutes). Minimum off time to protect cooling compressor. HA 194 Highest operating temperature limit (default at 194˚F). When exceeded the device will switch off the load and blink HHH. LA -58 Lowest operating temperature limit (default at -58˚F). When exceeded the device will switch off the load and blink LLL. CP 01 Temperature Differential Setting. 01 is my setting (default at 02 or 2˚F). Turn on at 1˚F below temperature setpoint. If my temperature setpoint is 77˚F, heater is turned off when temperature reached 77˚F and turned back on when temperature dropped to 76˚F. The aquarium is always between 76˚F and 77˚F, a 1˚F temperature differential. Set: Press once to change temperature setpoint. Then press once return to display measured temperature. Hold for 3+ seconds to access parameters setting menu. Press "Set" to accept and exit settings menu after configuring a parameter. Rst: Press once to exit current setting. Press and hold 6+ second to reset to factory defaults. UpArrow: Increases settings. When not in parameters setting menu, this sets the heat/cool setpoint. Hold for 2+ seconds to auto advance. DownArrow: Decreases settings. When not in parameters setting menu this sets the heat/cool setpoint. Hold for 2+ seconds to auto advance. DownArrow: From main display of measured temperature, hold for 6+ seconds to lock parameters from being changed (display shows "OFF"), temperature setpoint is NOT locked and still can be changed; hold another 6+ second to release from lock mode (display shows "ON").
December 8, 2017
instruction on how to use it is somewhat cryptic but if you have a knack on tools and software it isn't too hard to figure it out. The reason I took off a star is because it doesn't have information on how much power it can switch. Can I hook it up to a 1kW submersible heater? honestly I don't know. Probably not. but I can use it to switch an external high powered electronic switch to boost the power level. There are lot of use for this thing and it was definitely $saver and time saver instead of building one myself using "Arduino" controller. Really can't beat the price and its debugged. Some of the uses. heat my proofing box for bread baking. Heating for making yogurt. Heating my germination table for plant starts. Aquaculture, aquaponic, hydroponic use. I'll probably buy few more. May use it for incubating chicken eggs.
By Jer R.
December 4, 2017
It took some experimenting , but I got this controller working super. The instructions need some work for clarity. After reading several times and trying different things the process begins to fall in place. The hook up diagram was the easiest of all. I used some existing power cords and I started by cutting the receptacle end off and using the cord for the power hook up. Now you can use the receptacle end for the load hook up. One more short wire from power to load and you are there. Just follow the diagram without any deviations and it works. The display is in bright large easy to read numbers and letters. The project I'm using this on requires the controlling of a set high temperature to click on and a low temperature to cut off. It took some time to get the controller working right, but it's doing a good job with very precision settings. Looks like this controller can be used in a variety of different ways for other applications. Ten amps @ 120 volts will be more than enough for my project.
December 2, 2017
This one displays in Fahrenheit. I use this for sous vide cooking. Unlike the STC-1000, this model has only one relay. It can be used to control either heating or cooling. It powers up in the heating mode by default. Changing to cooling mode is programmed via the "Set" key. The instruction is not well written, but it is not that difficult to figure out how to program the unit. I put this controller into a 4.7x4.7x2.2in Hammond 1591 USBK ABS plastic project box, which is also available from Amazon. It fits nicely inside this box, with room for a Amico 3 pin power socket for plugging in the load. It is very easy to wire up. The relay is rated at 10A, so I use a 16 AWG power cord as a supply cord. The temperature sensor cord is a bit flimsy, but it works. For $17, I can't complain!! Can easily replace this 10K NTC sensor if broken. I already have a Johnson Controls A419 controller, but I need another controller. This is a much lower cost alternative. It is so inexpensive, I also put together another unit for a friend.
By Scott (Technogeek)
November 26, 2017
I wanted to make a Sous-Vide cooker out of my old crock-pot, and this was perfect. I just purchased a 10amp 3 wire extension cord, cut it in two, then wired it up per the included schematic. The cord wires attach via enclosed lug-less screw down terminals, so they are firmly attached. The wiring terminals have a removable plastic cover so any exposed wire is safely out of reach. Once he cord is installed, plug the cord male connector into the wall outlet, and the Crock-pot into the female cord end. Set the Crock pot temp to high, adjust this temp controller to your desired temp and your done! Programs super easy and works great, regulating the temp +/- 2 degrees in my Crock-pot. Manual is the usual Chingalish quality, but this thing is easy to figure out.
November 23, 2017
I have another one that displays only in Celsius. Both of them work well, but I like being able to use Fahrenheit. I am currently using this for a Sous Vide application in a cooler with an aquarium circulator pump and an immersion heater for culturing yogurt. It reads about 2 degrees F high at the target temperature of 110 F (as read with an electronic thermometer), so I set it to 112 F. I have worked with a number of temperature sensors and I find this to be very acceptable. They all need to use calibration curves, so one should always measure the actual temperature after they are at the target and adjust appropriately.
November 22, 2017
I purchased one of these about a month ago to control the under tank heater in a lizard cage. Previously I had been using lamp dimmers, but got tired of constantly adjusting them based on the ambient temperature of the room. I had also tried using a more expensive dial type thermostat designed specifically for reptiles that was about twice the price and had no features. When I received the first one of these, it worked so well that I ordered four more. They all arrived yesterday, so now I'm wiring them to the rest of the critter cages. So far, the only problem I have with these is the instructions that are included. The wiring diagram is pretty straight forward and the settings can be easily figured out. So far, very happy with this item.
By T Smith
November 20, 2017
Module powered up and functioned immediately. I built a box for it and associated power cabling, all went well on first assembly. I'd recommend socketing the temperature probe - I used a mini headphone jack on my project box. If you're not clear on the settings: when used for heating, you set the MAXIMUM temperature, where the relay cuts off, and the DIFFERENCE in degrees between the max and the minimum temperature. So for my use I set it at 38 degrees max, and a difference of 4 degrees: the relay turns on at 34 degrees (38-4) and turns off at 38 degrees). I wish I could deduct a half point for the directions, they are OK but a bit opaque (a medium quality translation, not horrible but needs work to explain things so a less experienced person could use it easily).
By david B
November 20, 2017
Je cherchais une solution pour réparer ma tireuse à bière, voilà qui est fait. Le contrôle de la t° de ma tireuse à bière ne fonctionnait plus, alors que le groupe de froid est vraiment excellent. Ce contrôleur lui a éviter de partir à la poubelle. L'avantage de ce produit est qu'il est livré complet avec sa sonde de T°. Relativement compact, un afficheur de taille et d'intensité parfaite, il est relativement facile à configurer à l'aide de la notice fournis. Il aurait été plus aisé d'avoir cette dernière en Français, mais même avec mon petit niveau en Anglais j'ai pu le paramétrer facilement. De plus il est équipé d'un système qui permet de clipser le cache de la façade, ce qui permet de l'intégrer facilement dans un petit boitier, un meuble ou n'importe quelle installation. Il est capable de contrôler autant une plage de froid (frigo, congélateur, tireuse à bière, ...), qu'une plage de chaud (couveuse, aquarium, ...). C'est le 1er paramètre à sélectionner dans le menu. Le mien est en place depuis presque 1 mois et fonctionne parfaitement. A voir la fiabilité dans le temps ...
November 16, 2017
Réception dans les 48 h et en très bon état .Surpris car on me donnait un délai de 15 jours. je viens de le raccorder pour une utilisation de chauffage avec un ruban autoregulant en exterieur afin d'éviter que mon palmier ne subisse trop de très basse température.Fonctionne aux petits oignons. J'ai comparé la sonde avec un thermomètre digital qui mesure aux dixième.Et la je m'apercois qu'il me rend une température équivalente de l'ordre du dixième de degré .Magnifique. La doc est en anglais mais il est facile de la trouver sur internet. Bon maintenant je ne sais pas dans le temps ce que ca va donner mais aujourd'hui j'estime avoir fait un très bon investissement. J'espère que ces infos pourront en aider d'autres.
November 15, 2017
Finally have been able to install my temperature controller. It works as advertised and nothing more. Understand that this does heating and cooling but only one at a time. So you have to set and reset to the heating or cooling mode to which it opens the thermo-coupler differently. In the cooling cycle it does give some delay to save the compressor if you use a fridge or freezer. I was prepared with different instructions but actually the enclosed ones were easy to follow as well. Just some basic knowledge of electricity is needed, nothing complex. In my case I just added the thermo-coupler to an outlet in which I add a freezer or heating device such as an old lamp. I just wish there was an easy case to build this in. Oh yeah, I have no idea what the orange brackets do and if they even come off as I would want. I assume these are to build the device into a case and to press against the back to keep it in.
November 10, 2017
Sur le schéma de la notice l'objet "LOAD" désigne la place de votre appareil. Par exemple pour moi c'était un frigo. Dans le schéma je remplace le mot "LOAD" par les mots "LA PRISE SECTEUR DE MON FRIGO". Le reste de la notice se comprend aisément par quiconque de vos voisins ou amis ou membres de votre famille ayant fait même un tout petit peu d'anglais. Bref j'ai réglé le thermostat défectueux de mon frigo à fond. J'ai scotché le nouveau contrôleur à l'extérieur sur la paroi du frigo et j'ai mis la sonde à mi-hauteur à l'intérieur en enfonçant légèrement la tôle pour laisser passer le fil de sonde sans géner le joint de porte. J'ai fait le montage et les réglages et "Nickel Chrôme" le frigo fonctionne mieux que jamais. Ce thermostat est de haute précision, de quoi garantir une hygiène irréprochable.
By John C.
November 8, 2017
Unlike some other very similar offerings here on amazon, this unit can only be set up to heat -or- cool. If you are looking for a solution to be able to do either on the fly without reconfiguration, this is not your item. (one is branded as "Elitech All Purpose Temperature Controller" 2-relay, but there are others). That other item is virtually the same price, the manual is in [better] english, and the contacts come labeled in english as well. Other than the single-relay and abysmal english, though, this isn't a bad purchase. (I even submitted part of the manual on this item to engrish dot com! it's that good!)
November 2, 2017
Bought this for use in my fermenting refrigerator. Search google for wiring instructions, there are better ones out there than what's provided with the controller. It's rather simple to wire up and get working and so far it's made the single biggest difference in my beer brewing. I'm VERY happy with this cheapo solution. There are a couple of things to note: 1. This is a single stage, meaning it can only turn on one outlet. So in brewing, it's for turning the fridge/freezer on. If you need to regulate the temp even closer, you'll have to get the STC1000 which displays in Celsius only, but can also turn on a lightbulb or something to heat when it gets too cold. This obviously gives you much more precise control. I live in Florida where I only need it to cool, so I'm good there. 2. There's a 5 or so degree window in it's accuracy. In other words, if you want it to operate at 65 degrees, it won't kick on until it gets to 68, then it will cool down to 63 before turning off again. No big deal for most, but again, if you demand absolute accuracy.... Overall and for the price, I'm very pleased.
February 26, 2016
The MH1210F is a single stage temperature controller which means it can heat or cool but not at the same time. The wiring connections are straight forward and the included temperature probe and wire are thin. I used left over water supply copper tubing to make a water tight enclosure for the probe so it would not be submerged in hot water for hours on end. Not sure if this is necessary but it may help prolong the life of the probe. I originally bought the MH1210F for cooking Sous Vide using a crock pot and it works great. I ended up giving the enclosure (7x5x3") to my brother and I built a smaller one (6x4x2") using the ITC-1000F from Inkbird. See my review for Inkbird All-Purpose Digital Temperature Controller Fahrenheit & Centigrade for more information. The chinese-english translated instructions for the MH1210F is practically incomprehensible so here are cleaned up instructions. Set Key - Set temperature / Settings menu / Select setting / Save setting value Rst Key - Exit settings menu / Reset to default values Up Key - Up settings menu / Increase value Down Key - Down settings menu / Decrease value Press Set once and the display will blink. Press the up or down keys to increase or decrease the set temperature. The new set temperature will automatically save after a few seconds. Press and hold Set for 3 seconds to enter settings menu. Use arrow keys to select setting, then press Set to select and press arrow keys to cycle between options. Press Set to save settings and Rst to exit settings menu. HC - Heat or Cool mode CA - Temperature Calibration -10F to 10F, default 0F PU - Compressor delay 0min to 10min, default 2min HA - High limit, default 194F LA - Low limit, default -58F CP - Differential activation range 1F to 30F, default 2F Press and hold Rst for 3 seconds until display blinks to reset all settings to default values.
Heiß Ereignis Mehr
Meist gekauft Mehr
Ihre Frage wurde erfolgreich eingereicht
Bitte aktivieren Sie Ihre Registrierungs-E-Mail. Wenn nicht empfangen, klicken Sie auf die Schaltfläche unten
Unsere Website läuft von Cookies