Preis nur auf die App:
Diese Seite wird jetzt geladen....
Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
DC 12V-24V 3 Channel DMX Decorder LED Controller für RGB 5050 3528 LED Strip Light
Kontroller bietet alle Manipulation von Beleuchtung, bedeckt fast alle Bedürfnisse. kontrollieren Sie alle Farben, Farbton und brightess der RGB-Streifen Licht
Es kann standard DMX-512 digitale Steuersignal empfangen und
es in PWM-Signal verwandeln damit LED justieren.
Es kann mit DMX digitale Konsole verbindet werden, um RGM Dimmfunktionen zu erreichen.
DMX-Adresse kann über DIP-Schalter eingestellt werden
Zwei Signaladresse: XLR-3 und RJ45
Mehr als 15 Modes und 31 Geschwindigkeiten sind zu wahlen
Eingangsspannung: DC12 ~ 24V
Max. Ausgangsstrom: 8A (jeder Kanal)
Max. Ausgangsleistung: 288W ~ 576W
Anschlussart: Common Anode (+)
Betriebstemperatur: -20-60 ℃
Produkt-Größe: 16.5 * 6.5 * 4cm / 6,5 * 2,6 * 1.6in
Gewicht: 310g / 10,9 Unzen
Packungsgröße: 18 * 7,7 * 5cm / 7,1 * 3,0 * 2.0in
Paketgewicht: 400g / 14,1 Unzen
1 * DMX-Decoder
beyogen auf 101 Kundenbewertungen
Sagen Sie Ihre Meinung mit anderen Kunden und erhalten Tomtop Punkte, die ersten 5 Bewertungen bekommen DOUBLE Tomtop Punkten!Schreiben Sie eine Rezension
By M. Boggs
November 24, 2016
Works as described. Wiring the LED strip was easy enough (4 wires, R, G, B, and White connectivity, remember this is the 3 channel version. If you need one that supports actual white LED, then you need the 4 channel one). I do wish they would just use a standard DC port for the power, instead of making you wire it. I use this for mobile DJ work, so packing it up when the LED strip and the power supply have to be attached like this, is inconvenient. Note: I was upgrading this previous purchase, so I had the LED strip and Power already. B00JP6LAPE For power, I just cut the end off, stripped it and wired it in. It was easy, as the inside of the cable was black and red, so it was easy to identify the positive and negative. I'm happy overall. Like I said, I wish it had a power plug, instead of hard wired. The dip switches seem a little flimsy too, so I need to be careful how I transport it. They might not break, but they could easily get moved to incorrect positions. I also wish it was smaller. Seems a little bigger than it needs to be. I should point out, that these are all pretty similar. Some only have Cat5 ports instead of DMX (xlr) ports, so you would need a special cable for that. This one has both. I prefer to stick to all DMX (XLR).
November 12, 2017
Viene bien embalado. El producto es bastante bueno: el fieltro es agradable al tacto, el velcro cierra bien, el ordenador cabe bien... La funda está pensada para proteger el ordenador cuando se lleva en una mochila o en una maleta. Si se usa como funda de mano de forma diaria, el fieltro termina por rozarse y ensuciarse. La protección del ordenador es prácticamente nula a los golpes y mucho menos a la lluvia. Lo compré para llevar en la mochila ya que ocupa poco pero compré otra funda para llevar el ordenador en la mano, por lo que estaba buscando que fuera fina y con un diseño bonito. ¡Pero ojo con usarla como funda de mano!
By Khalid Asad
December 14, 2015
This is my review for the Lixada 5M RGB LED Strip. WHAT YOU GET IN THE BOX : You get 1 RGB LED strip, one power brick, one LED controller, one LED controller controller, and an instruction manual. BUILD QUALITY : I am VERY impressed with the build quality of this product. The RGB has a thick silicon coating, that will make it much more durable in the long run, and would likely make it much more resistant to the elements. The box and power brick are just plastic but I expect nothing more, and the controller is good. Great job on the build quality! FUNCTIONALITY : These are perfect, except with one big gripe. The LED strip is very bright and frankly gorgeous, and the silicon coating helps better diffuse the light, giving a more consistent glow rather than the segmented glow some other strips suffer from. The controller works good and there is a good amount of customization. My main gripe with this, and by far the biggest flaw IMO, is that there is no adhesive on the back! This is something I had definitely come to expect on an RGB strip, I had planned on putting this on the back of my desk for cool lighting, but now this will be much more of a hassle, because I have to deal with zip ties and such. OVERALL : Overall, I would recommend this RGB strip. These are obviously meant to be used outside or other places to where they would be subjected to harsh conditions, and this is why I assume they didn't bother putting adhesive on the back, but I still would've really appreciated it being there, or at least a note somewhere on the page.
By Paul K. Mckneely
December 11, 2015
Whoever wrote the user manual for this product had a very poor grasp of English. I have read through the reviews and questions and there is a fair amount of misinformation and misunderstanding of the subjects related to the operation of this device. I purchased one of these DMX decoders to test an LED lighting controller that I have been developing over the past several months. Its target customer base is filmmakers. Because I will be using this device in my development I would like to provide a mini user manual for this product since the one that came with the device was so poorly written. I will add to this review as I learn more about it. On the back of the unit is a 6-position termination block. Proceeding from left to right, the 1st contact is Ground (labeled V-) and the 2nd is Power (labeled V+). This powers both the unit and provides power to the LEDs via the other four terminals. This unit can use DC power from +12V to +24V so make sure that you supply the voltage that is needed by the LED load you intend to connect to the unit. The 3rd terminal position is labeled COM and it is presumably internally connected to the V+ terminal. The last three pins labeled CH1, CH2 and CH3 are drain pins for each of three lines of LEDs. Standard RGB LED strands have a flaw in the design of their connectors in that all of the channels share the power pin while each color has its own ground pin. Since each contact in the terminal block has a limited current rating, the amount of power that this unit can supply will be limited by the COM pin since it must supply all power that is drained by the combined channel pins CH1, CH2 and CH3. On the left side of the "front" of the unit is a 10-position bank of DIP switches. In all of these switches, the DOWN position is considered to be ON while the UP position is considered to be OFF. The position of switch 10 determines the meaning of the other nine switches. When OFF the positions 1~9 are used to specify the device's DMX bus address. The value that each position contributes to the bus address is 2 ^ (N-1) where N is the switch position.
December 6, 2015
The unit worked as expected. In my case, I was using the XLR sockets, not the RJ-45 sockets. Set up the channel, added inline to the other lights, ran power to it. Using it to control two 5-meter RGB strip lights (in parallel) on a stage. Only CON I really had for it was the dip switches. they get knocked pretty easily and you need to re-confirm the channel you want the device set to if you fiddle with it at all (or move it around). They are very "flimsy" in that sense. All in all, works as expected.
By Matt Olson
November 12, 2015
If you're looking for a product with clear to follow instructions and an intuitive hookup, look elsewhere. This product has a "COM" terminal (Common annode for those who know about LEDs) and their instructions say to not use the COM terminal. The instruction manual has many misspellings and hard to follow grammar. There is no indication on the DIP switches on which direction is ON. However, once I got the hookup correct, the test functions were very nice. I haven't hooked up to a DMX controller yet but once I get back to my lighting console I fully plan on it. All in all, this seems to be a decent DMX to LED converter/decoder, but just don't depend on the instruction manual.
January 4, 2018
December 31, 2017
Es de muy buena calidad. Si el ordenador tiene puesta una carcasa entra un poco justo, pero no es ningún inconveniente porque no es nada exagerado. Es tal cual se describe en las fotografías. La funda pequeña para el cargador va perfecta también. Muy satisfecho con la compra.
By INDIRA BLUME
December 28, 2017
Se lo he regalado a mi chico para su Ipad de 9,7" Nos ha gustado muchísimo a los dos, el color es muy bonito. Y es perfecto tanto para hombre como mujer. Por dentro tiene terciopelo, y dos compartimentos. Es un pelín grande, pero al no haberla más pequeña... cogimos esta. La bolsita que trae independiente es también perfecta. Por el precio es una compra buenísima y una ganga. El está encantado con su regalo
December 18, 2017
En la funda para Portátil 12 pulgadas cabe perfectamente un Mackbook Pro 13 de los nuevos (de Late 2016 en adelante). Tiene un buen acabado para el precio que tiene, con varios bolsillos para meter pequeños objetos (cables, memorias USBs o tarjetas SD). La bolsa extra es muy práctica para llevar por ejemplo un HD externo o el propio cargador del portátil.
By romina barreiro medina
November 11, 2017
December 20, 2015
September 26, 2015
May 5, 2015
April 17, 2015
March 3, 2015
January 5, 2015
January 2, 2015
January 2, 2015
December 23, 2014
Heiß Ereignis Mehr
Meist gekauft Mehr
Ihre Frage wurde erfolgreich eingereicht
Bitte aktivieren Sie Ihre Registrierungs-E-Mail. Wenn nicht empfangen, klicken Sie auf die Schaltfläche unten