Meterk Professional 4 In 1 Wire Crimpers Техническое обслуживание Ratcheting Terminal Клещи для обжима наконечников Угловые наконечники для обжимных наконечников

It is a cool crimping tool. There is no wire end you could not terminate with this tool, in a household or in the office. It is built for everyday use. The plier is entirely made from steel, and the handles are covered with a yellow-black plastic, with a rubber insert in the handles, so you can grab it surely. The tool arrived in a zipper case. The plier is in the right part of this case, secured with a hook-and-loop strip. The left part of the case contains four socket. These sockets contains the three replaceable crimping inserts, and the four socket contains replacement screws. The middle part of the case holds a hex/philips screwdriver, it is useful when you have to swap the crimping inserts in front of the plier.Pushing the plier you could its ratchet, and after pushing there is a spring mechanism which opens it up again.

1. 
2. 
3. 

Dang you shipped this like way too fast, one of the Quickest Thanx. This tool is very well made for the $ like to get some extra different jaws just to have. yes there are way better made tools of this that do not justify their cost unless you use it in a trade every day. but for my electrical hobbies this is the ticket works so much better than my standard hand grip ones. If you were my friend i'd buy you one, well you are not but i'd recommend this to any one that loves RC, trains, car audio and anywhere there is a connection to be crimped appropriately.

These wire crimpers have made my electrical project a breeze. I was able to fasten all of the connectors to all the gauges of wire I had without changing tools once! These will crimp just about any end piece to any gauge wire within reason. I recommend these to anyone that does any type of electrical work on the regular, or anyone that has a single project on the horizon that would benefit from the use of these ratcheting crimpers! The ratcheting is great, as it holds onto the end piece until you have fully crimped it to the wire even if that takes more than one squeeze!

I've been using another crimping tool that just never did the job, so I started looking for a new tool and liked that this model had interchangeable crimpers. My only complaint is that the 1601-01 crimper jaws aren't color coded to US standards. So: Blue Dot = US Yellow, Red Dot = US Blue, and Yellow Dot = US Red. Since this is strictly cosmetic is doesn't rate a star, but wanted to note it here for those that might not understand there is a difference. Another note, is that there is a "right way" that the jaws go into the crimper. The lower gauge (thicker) goes in deepest. I tried it the other way around, and the bolt wouldn't screw in, which is a good thing, as that means that the correct amount of tension will be applied to the appropriate crimp size, so if you find yourself frustrated that the screw won't mount, make sure you have the jaws in the proper direction. I typically use a heat-shrink style of connector, and using the 1601-01 crimper jaws, the crimps using these types of connectors were perfect! They did not pull off, even before heat-shrinking and pulling with quite a bit of pressure! They also didn't "break the skin" of the heat-shrink plastic, such means that when heated there was no exposed metal that might cause a short. Now when it came to using a hard-plastic connector (which to be honest I've never had any luck with, using any crimping tool, which is why I don't use them), the 1601-01 crimper jaws did not actually crimp down onto the wire; it pulled right out. I started with the largest, and even recrimped with each smaller size, and the wire pulled right out after using all three. I switched to the 1601-06 crimper jaws, and the crimp held quite well, even when I applied a lot of pulling pressure; it did leave more of a mark/pinch on the plastic of the connector, but it didn't shear the plastic so there was no potential for short. I've included pictures of both types of connectors. The heat-shrink style of connectors,the miscolored dots, the case, pictures of using the 1601-06 which created a strong crimp using the hard plastic connector, but resulted in a bit of a pull/pinch in the plastic jacket. The last picture shows using the 1601-01 crimper jaws, and how none of them actually crimped onto the wire All and all, I'm very pleased. The case keeps everything organized, and it comes with extra mounting screws for the crimper jaws (which is a nice touch).

At first glance a good tool, fast sheeping

the product meets the expectations.

Alles Prima, danke. Gerne wieder

alles i.O.,schnelle Lieferung

genau wie beschrieben, Danke

A nice solid wire crimping tool with a 3mm hex/phillips screwdriver. Thanks

SUPER FAST Shipping! Item arrived as described. Happy Camper here.

works like advertised

A++ FAST Delivery. WELL Packed. Goods as Described. THANK YOU!!!

This was a nice little kit for the price. It is now it my husbands collection of tools he carries with him.

These crimpers are amazing, great deal, very fast shipping, thanks

I was really excited to get this as I like to have very good connections on the cables that I'm putting together. Everything came and a nice little kit and worked exactly the way I expected it to. All the parts are quite heavy duty but are easily changed out. It's definitely a good tool to have if you're an electrician or preciate having nice solid sturdy connections.

I don't even want to think about how many manual crimper tools and crimps I have had to make over the years. This one beats them all. The racheting crimp provides an even pressure and positive crimp every time.

Some dies quality not so good. But cheap.

Item as described. Quick delivery! Many thanks

makes great crimps