GoolRC Mini HD 700TVL 1/3 "Obiektyw 3.6mm CCTV Video Security FPV Kamera kolorowa NTSC

I purchased this camera for a FPV system to be used on a multi-rotor (quadcopter). The video quality from the camera is excellent, and the included plug makes it really easy to deploy on a FPV system. The metal construction of the camera case does have its attributes and detriments when using it for an FPV system. Of course, the biggest plus in my opinion concerning the metal construction is that it survives crashes very very well. My first quadcopter probably spent more time on the ground than it did in the air, and this camera kept on ticking, lick after hard lick on the ground, and concrete parking lots. Of course, the same thing that saved my camera from being destroyed in hard crashes, actually helped to contribute to the crashes due to the weight of the metal frame. This little camera is quite heavy. I was initially using it on a SYMA X8C and with the camera and FPV transmitter attached to the quadcopter, it was a little sluggish in its response, and while it was able to carry the camera, it definitely impacted flight time, by reducing it from 15 minutes flight time to about 8 minutes flight time. Bear in mind.. the SYMA copter is NOT designed to be carrying around a lot of FPV gear, so it's to be expected that it's not going to perform well. However, had the case been made of plastic instead of metal, there would have been a definite performance enhancement. Here are the primary reasons that I like this camera. 1.) Image quality is outstanding!! 2.) Its metal case protects it from more severe quadcopter crashes. I have crashed this thing into concrete parking lots more times than I care to admit, and it is still working! 3.) Power requirements for this camera seem to be very low. Here are the things that I think can be detriments to the camera. 1.) Metal case - Yes, it's a plus and a minus. If you're flying a cheap quadcopter, this camera is going to be heavy to lift, and will cause your quadcopter to consume more power, thereby shortening your flight time. 2.) I am concerned about the little plug that comes with the camera. If it gets lost... there's not a resource for getting a new plug, which means that the camera is in effect un-usable. For my application, I hot-glued the plug into the socket so that it cannot be removed from the back of the camera. It works great, and just ensures that it never comes out of the camera. 3.) Field Of View - While this camera does have sufficient field of view to be used as a FPV camera, I would like just a little wider view. I'm probably being overly picky here, because if I could, I would have a fish-eye lens attached to it for maximum field of view lol. Having said that..... I think for most FPV applications, this little camera is very adequate, but for some racing scenarios, you may want a slightly wider field of view. All in all, I would highly recommend this camera for FPV use on high-quality multi-rotor machines. -Kai Lerner (Photographer)

The camera works well in daylight, and in well-lighted artificial light situations. It works unexpectedly well in low-light conditions, too - although it is definitely not "night vision". It does not switch to black & white under low-light conditions, so the color images produced under those conditions are very grainy. It has a metal housing and mounting bracket, although the housing is not sealed around the cable connection, so it is not really weather-resistant. It is easy to mount and aim; the bracket has a center hole threaded for a metric mounting screw (NOT included), so no need to fumble with a nut. Also has slots for inserting (a) screw(s) to secure the aiming position - although snugging the center mounting screw is adequate for holding the aim in static situations, because the unit is fairly lightweight. The bracket can be swung up or down to allow mounting from above or below. The housing is robust, and probably could be made essentially weather-resistant if the connector opening and seams were sealed with RTV, etc. The only other improvement that might help would be to have black & white mode and an IR cut filter - for clearer low-light images.

So I got this for the Cheerson CX-20 drone (a clone for the DJI Phantom). I soldered to a video wire that connects to the transmitter so I can get feed. When I checked my FPV goggles though it didn't receive a signal, so I cut and soldered another cable and still no signal until I realize on the back of the camera it needs a 12 volt power source to run and luckily, there are 12V ports on the bottom of the CX-20. I only connected the Power & ground wire to the 12V while the video cable is still plugged into the transmitter. I then checked my goggles and then I see live-active feed. Would recommend this for FPV fliers but be aware with the camera!

Well. Can't comment on video quality as this camera was wired the opposite of mine. So I burned up the camera and transmitter trying to use it.. So be aware of the wiring. Other than that I love the frame and being able to point it at the angle I want.

The metal casing is too heavy for my quadcopter

nice item. Shipped quickly

I received my camera undamaged and worked fine.But it was knocked off in the next few days.And can't received the signal,the data can not be transferred .I think it is a fake.It does not perform as specified, reguardless how inexpensive, it is a rip. I will think twice in the future.Anyway fairly good product.

awsome product i am very happy with my purchase😀

small size, good picture, for indoors use. Not weather-proof

It's a little heavy because it has an all metal case and metal lens frame. Hopefully it will be robust for crashes. Video quality seems ok for FPV. It does not have any mounting holes on the back of the case to attack to my quadcopter's front facing FPV mount. I'm going to try just ziptie'ing it to the lower frame board.

Good for the price. Removed one star because the lens is built into the case which is unfortunate if you ever want to remove the board to save space.

ok so I'm giving this 4 stars because I planned on using this for fpv, but it's too heavy in my opinion. Some people may be ok with shorter flight times and added weight, but I want to keep my weight down as much as possible because my quad is already on the side of heavy. Otherwise, I got the camera on and it works well, even has adjustable focus with a little screw. You cannot remove it from the casing! the casing contains the lens.

The heavy metal case cannot be easily removed. The lens is held on as part of the case, so you'll need to rig something up to fix that if you want to remove the case.

It's a great camera for the price, but as other reviews have said, it's very heavy. The colors are great, but the light/dark contrast could be better. At only $10, it's a great deal someone looking for a cheap FPV camera.

The case is made of steel and, although gives protection to the PCB, adds a lot of weight to an FPV system. Better video quality than many others- I still use it on my 250quad

I have an Arris X-Speed FPV 250 quad that came with a "board camera" which is not nearly as good as this one is. It is heavier due to the metal case that is one draw back,however it is well protected. I will be buying another of these. Great camera for the money!

For the price it isn't all that bad. I use it for flying FPV with my home built multirotor.

It works great.

Excellent camera for the price, however would not recommend this specific lenses for aerial FPV, have since purchased a replacement lense and it definitely improved performance

Excellent camera. Use for FPV quad. Only issue is the weight of the camera body. It is made of metal. Would rather it be made of plastic but it was not designed for FPV use.