Cena dotyczy tylko aplikacji:
Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
yes,it have a 3/8" thread hole on the bottom. it can be directly mounted onto any ball head, tripod, gimbal and monopod.
By andoer SELLER on February 8, 2018
The round base plate is 2.375" in diameter. The fixed side of the clamp lip (the side with the leveling bubble) is 1.875" wide. The movable clamp lip is 1.75" wide.
By California Bill on October 25, 2017
I believe a pu-70 is longer than a pu-50 not thicker.
By John M on October 2, 2017
Good day, funny, I had the reverse problem when I first received this clamp. It wouldn't close enough. But when I disassembled it, I found two springs, that were too long to allow the clamp to close tightly. I trimmed about two turns off each spring and it works perfectly for me. But, as far as opening, mine opens enou… see more Good day, funny, I had the reverse problem when I first received this clamp. It wouldn't close enough. But when I disassembled it, I found two springs, that were too long to allow the clamp to close tightly. I trimmed about two turns off each spring and it works perfectly for me. But, as far as opening, mine opens enough to top loads with no problem. Sorry for your troubles!!! Keep shooting! see less
By Randy Frieder on July 20, 2017
Pamiętaj, że Forum TOMTOP to społeczność pomagająca wymieniać się pomysłami i pomagać w poszukiwaniu, podczas których entuzjastyczni technicy będą uczestniczyć w dyskusji, tymczasem obsługa klienta TOMTOP (z ikoną obsługi klienta Tomtop) będzie odpowiadać na czas, z tą samą funkcją, co kontakt na http : //www.tomtop.com/contactsotwórz to forum na całej stronie
oparte na 35 Opinie klientów
Podziel się swoją opinią z innymi klientami i uzyskać Tomtop punkty, pierwsze 5 opinii dostać DOUBLE Tomtop Punkty!Napisz Recenzję
November 20, 2017
I like this Andoer Arca compatible tripod/monopod head/clamp. I'm using it specifically for a monopod for telephoto lenses. The knob is short and wide for nonslip grip. Both ends of the clamp has plate stops to prevent over travel. The 70mm plate is generously long to fit on a lens foot or camera bottom. The 3/8" threaded adapter allows threading onto a 1/4" male thread or use the 3/8" screw to mount the plate and tighten with the enclosed hex key. The Andoer plate has the bubble level atop the plate without an additional spur/bump on the side that can snag against camera straps. The clamp edges are radiused and full length for ease of clamping without scratching and provide a tight grip. As another reviewer did mention, one side of the plate or base is 1/2 a millimeter off with the 0 marking. Thus one side is zeroed, but the other a mil off mark. No big deal in my mind. If anyone is really going to rely on the ruler marks, then get another brand/model that's 3-5 times the cost.
November 17, 2017
By ALTON A. ALEXANDER
December 3, 2017
By From London
November 29, 2017
November 20, 2017
November 18, 2017
By Lori JE
November 12, 2017
November 11, 2017
October 26, 2017
I originally got a regular quick release with a pull lever. That was pretty cumbersome for my needs so I returned it for this one. This one is more simplistic and I like you just twist to tighten and loosen the plate. I learned these are called Arca Swiss. I also like how the bottom is smooth and flat and has more areas to grab onto a tripod/monopod.
By Daniele Schipa
October 23, 2017
By Norbert Siebert
October 7, 2017
By Bill Mahon
August 28, 2017
June 14, 2017
By I Waterman
June 14, 2017
May 12, 2017
April 22, 2017
By John V.
April 17, 2017
Works great. The effective clamp length is about 46mm - plenty for most purposes. The base diameter is 60mm. The unthreaded side mount holes are on a 45mm circle - compatible with RRS, Hejnar etc. The shift scale would be more helpful if it just went from +/-15mm in mm steps, instead of +/- 0-5mm,7.5mm,10mm. Weird.
April 8, 2017
By Daniel H.
February 20, 2017
November 7, 2016
I liked this so much that I bought a second one. It's a great option for Arca Swiss, doing the job just as well as base & plate combos costing 2 or 3 times as much. But for Chrissakes, that is NOT a 1/4-20 screw that you're including in this. It's a totally different thread pitch. If you swapped that out for a real 1/4-20 screw, this would be a solid 5 star product.
Hot Event Jeszcze
Najlepsi sprzedawcy Jeszcze
Twoje pytanie zostało przesłane pomyślnie
Please activate your account and then to buy,We will resend the activation email to help you complete your registration.