Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
Q & A
Depending on what size wire you are crimping. works great for most wires in an auto. Dose not work for larger wires, 10gauge is two big. I hope this helps
By Monte J. Sime on April 17, 2018
Depends on the die, I guess... Haven't tried it... Spark plug wires would be well within its pressure capacity, though...
By M. Sloan on January 16, 2018
JST? I don't mess with microelectronic terminals of that nature so I can't answer that. Dupont connectors should be fine. There is a set of heads in this kit specifically for the smallest of terminals and they're real effective in crimping a new set of TE Connectivity Super Seal terminals to refresh my Jeep PCM.
By J. L. Freelong on January 3, 2018
looked at dupont conectors just dont know untill i tried, sorry using mine for solar wiring connections very specific dies for that and they work well
By StRyKeR on December 22, 2017
It does in fact!
By Christopher S.C. on November 21, 2017
By Kindle Customer J on November 7, 2017
I don't know
By Mark J Fletcher on November 4, 2017
Not sure but it seems to have every type of crimping attachment but I haven't used it on that type.
By MDG on November 2, 2017
It works good
By scott halsey on November 1, 2017
I do not know. It does have a open barrel crimp die but not sure that will work on molex mini-fit jr
By S. Green on December 28, 2017
に基づいて 68 お客様の評価
October 6, 2017
It is a cool crimping tool. There is no wire end you could not terminate with this tool, in a household or in the office. It is built for everyday use. The plier is entirely made from steel, and the handles are covered with a yellow-black plastic, with a rubber insert in the handles, so you can grab it surely. The tool arrived in a zipper case. The plier is in the right part of this case, secured with a hook-and-loop strip. The left part of the case contains four socket. These sockets contains the three replaceable crimping inserts, and the four socket contains replacement screws. The middle part of the case holds a hex/philips screwdriver, it is useful when you have to swap the crimping inserts in front of the plier.Pushing the plier you could its ratchet, and after pushing there is a spring mechanism which opens it up again.
By Eric S.
November 7, 2017
Dang you shipped this like way too fast, one of the Quickest Thanx. This tool is very well made for the $ like to get some extra different jaws just to have. yes there are way better made tools of this that do not justify their cost unless you use it in a trade every day. but for my electrical hobbies this is the ticket works so much better than my standard hand grip ones. If you were my friend i'd buy you one, well you are not but i'd recommend this to any one that loves RC, trains, car audio and anywhere there is a connection to be crimped appropriately.
June 13, 2017
These wire crimpers have made my electrical project a breeze. I was able to fasten all of the connectors to all the gauges of wire I had without changing tools once! These will crimp just about any end piece to any gauge wire within reason. I recommend these to anyone that does any type of electrical work on the regular, or anyone that has a single project on the horizon that would benefit from the use of these ratcheting crimpers! The ratcheting is great, as it holds onto the end piece until you have fully crimped it to the wire even if that takes more than one squeeze!
June 10, 2017
I've been using another crimping tool that just never did the job, so I started looking for a new tool and liked that this model had interchangeable crimpers. My only complaint is that the 1601-01 crimper jaws aren't color coded to US standards. So: Blue Dot = US Yellow, Red Dot = US Blue, and Yellow Dot = US Red. Since this is strictly cosmetic is doesn't rate a star, but wanted to note it here for those that might not understand there is a difference. Another note, is that there is a "right way" that the jaws go into the crimper. The lower gauge (thicker) goes in deepest. I tried it the other way around, and the bolt wouldn't screw in, which is a good thing, as that means that the correct amount of tension will be applied to the appropriate crimp size, so if you find yourself frustrated that the screw won't mount, make sure you have the jaws in the proper direction. I typically use a heat-shrink style of connector, and using the 1601-01 crimper jaws, the crimps using these types of connectors were perfect! They did not pull off, even before heat-shrinking and pulling with quite a bit of pressure! They also didn't "break the skin" of the heat-shrink plastic, such means that when heated there was no exposed metal that might cause a short. Now when it came to using a hard-plastic connector (which to be honest I've never had any luck with, using any crimping tool, which is why I don't use them), the 1601-01 crimper jaws did not actually crimp down onto the wire; it pulled right out. I started with the largest, and even recrimped with each smaller size, and the wire pulled right out after using all three. I switched to the 1601-06 crimper jaws, and the crimp held quite well, even when I applied a lot of pulling pressure; it did leave more of a mark/pinch on the plastic of the connector, but it didn't shear the plastic so there was no potential for short. I've included pictures of both types of connectors. The heat-shrink style of connectors,the miscolored dots, the case, pictures of using the 1601-06 which created a strong crimp using the hard plastic connector, but resulted in a bit of a pull/pinch in the plastic jacket. The last picture shows using the 1601-01 crimper jaws, and how none of them actually crimped onto the wire All and all, I'm very pleased. The case keeps everything organized, and it comes with extra mounting screws for the crimper jaws (which is a nice touch).
February 5, 2018
January 15, 2018
December 13, 2017
December 12, 2017
December 7, 2017
November 22, 2017
November 20, 2017
October 30, 2017
October 27, 2017
By M. Craft
October 24, 2017
September 5, 2017
By Christopher S.C.
July 6, 2017
I was really excited to get this as I like to have very good connections on the cables that I'm putting together. Everything came and a nice little kit and worked exactly the way I expected it to. All the parts are quite heavy duty but are easily changed out. It's definitely a good tool to have if you're an electrician or preciate having nice solid sturdy connections.
By ALAN G
May 28, 2017
May 1, 2017
April 24, 2017
March 16, 2017